您好,欢迎访问重庆液压升降机械销售中心官网!

重庆液压升降机械销售中心

 多年以来一直专注于生产销售液压升降机械设备

全国24H热线服务电话:

152-5313-4653

您当前的位置 :首 页 > 客户案例 > 固定升降机液压弯排机使用注意事项

固定升降机液压弯排机使用注意事项

2022-11-15 09:57:38
322次

1、先将固定升降机http://www.jnyuexiang.com/工作油缸伸进方档块孔内,将螺帽拧到底,使螺帽与方档块靠紧再旋紧蝶形固定螺丝,然后将压高管端部快速接头活动部外套向后拉,并套在工作油缸接头上手放松,活动部份恢复到原位即自行扣上,再将泵体上的放油螺钉旋紧即可工作,同样当工作完后将放油螺钉放松,工作缸就会自动回缩。
First fixed lifts operating cylinder bore into his side of block, tighten the nut in the end, so that the nut and the side of block abutting then tighten the screws butterfly, and then press the ends of quick connectors executives coat to the active portion after the pull, and set to get started in the working cylinder joints relax, moving parts back to the place that is self-buckle, and then pump the oil drain screw can be tightened on the job, the same job after the discharge of oil when the screws loosen, cylinder will automatically retract.

2、固定升降机平弯时打开上花扳将夹板模头部装进工作油缸头,根据所弯排的厚度,选择模板与铝排或铜排一起放进夹板模头中,然后压紧夹板将两只辊柱的槽宽对应向着铝排和铜排厚度,并且放入相应的尺寸孔中,再将上花板盖上,立弯时打开上花板,将直角模头装进工作油缸头部,在下花扳孔插上两只销子,再将上花板盖上,铝排或铜排放在销子与直角模头之间即可工作。
Open the flower head pull the plywood mold cylinder head work put into fixed lift-bending, depending on the thickness of the curved row, select the template with aluminum or copper discharge into plywood die together, and then the two clamping jaws corresponding column width roller toward aluminum and copper thickness row, and into the appropriate size hole, and then spent on board cover, turn spent on board when the vertical bending, the work put into the right angle die cylinder head, spend the next two pin pull plug hole, then spent on board cover, aluminum or copper exhaust emissions can work at a right angle between the pin and die.

3、固定升降机http://www.jnyuexiang.com/使用时如出现空打现象,可先旋松泵体上的放油螺订,将泵垂直起来头向下空打几下,然后而旋紧放油螺钉,即可继续使用,在有载荷时切忌将快速接头卸下。本机是用油为介质,必须做好油及本机的清洁保养工作,以免淤塞或漏油,影响使用效果。
Such as when using a fixed lift runaway phenomenon, can put the oil set to loosen the screw on the pump, the pump vertically up and head down a few dozen empty, then drain and tighten the screws, you can continue to use, there is avoid the quick connector when removing the load. This machine is oil as the medium, we must do the work of cleaning and maintenance of oil and the machine, in order to avoid blockage or leakage affect the results.

快速导航

· 产品展示                · 客户案例              

· 厂容厂貌                · 新闻动态              

· 行业知识                · 常见问题             

· 关于悦翔                · 联系我们             

联系我们

公司名称:重庆液压升降机械销售中心

联系人:安经理

电话:152-5313-4653

邮箱:347299818@qq.com

地址:重庆市经济技术开发区

手机移动端

微信扫一扫